I just received my 2nd RioCar that I purchased on Ebay. Upon hooking it up, I get No Hard Disk Found. After reading the FAQ I tried my Power Supply that works fine with my first one, Nope still not found. This RioCar came with only a 10gig drive and I have a 20gig on hand so I decided to replace the 10gig with a 20gig. I loaded the drive formatting utility with the new drive and still get drive not found. Below is the output from hyperterminal. Any help would be greatly appreciated.
Thanks
Kelly
ircomm_tty: virtual tty driver for IrC
empeg-car bootstrap v1.02 20001106 (
[email protected])
If there is anyone present who wants to upgrade the flash, let them speak now,r version 4.27 with no serial options enabled
or forever hold their peace...it seems not. Let fly the Penguins of Linux! UART
ttyS01 at 0xf8050000
e000 v1.04is a SA110
Copying kernel...
Calling linux kernel...02 at 0xf8030000 (irq =
Uncompressing Linux..................................... done, booting the kernes 206f6972 'rio '
empeg display initialised.
l.
Linux version 2.2.14-rmk5-np17-empeg49 (
[email protected]) (gcc versixer initialised
empeg dsp initialised
NetWinder Floating Point Emulator V0.94.1 (c) 1998 Corel Computer Corp.ort initialised 0089/88c1 (save to d0004000).
empeg-car player (hardware revision 9, serial number 40104282)d
empeg power-pic driver initialis
Command line: mem=16m
Calibrating delay loop... 207.67 BogoMIPSlized: 16 RAM disks of 4096K size
Memory: 15024k/16M available (964k code, 20k reserved, 372k data, 4k init)
Probing primary interface...
Dentry hash table entries: 2048 (order 2, 16k)
hda: TOSH
Buffer cache hash table entries: 16384 (order 4, 64k)
hda: TOSHIBA MK2016GAP, ATA DISK drive
Page cache hash table entries: 409
TCP: Hash tables configured (ehash 16384 bhash 16384)
empeg-flash driver initialized
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
smc9194.c:v0.12 03/06/9
Linux-IrDA: IrCOMM protocol ( revision:Tue May 18 03:11:39 1999 )
SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7
ircomm_tty: virtual tty driver for IrCOMM ( revision:Wed May 26 00:49:11 1999 )
a
Partition check:
hda
Starting kswapd v 1.5 hda1
SA1100 serial driver version 4.27 with no serial options enabled
empeg audio-in initialised, CS4231A revision a0
or forever h
empeg remote control/panel button initialised.guins of Linux!
empeg usb initialised, PDIUSBD12 id 1012
e000 v1.04
Copying kernel.
hda: TOSHIBA MK2016GAP, ATA DISK drive
hda: TOSHIBA MK2016GAP, ATA DISK drive
hda: TOSHIBA MK2016GAP, ATA DISK drive
hda: TOSHIBA MK2016GAP, ATA DISK drive
hda: TOSHIBA MK2016GAP, ATA DISK drive
hda: TOSHIBA MK2016GAP, ATA DISK drive
ide0 at 0x000-0x007,0x038 on irq 6
hda: TOSHIBA MK2016GAP, 19077MB w/0kB Cache, CHS=38760/16/63
empeg-flash driver initialized
smc chip id/revision 0x3349
smc9194.c:v0.12 03/06/96 by Erik Stahlman (
[email protected])
SMC9194: SMC91C94(r:9) at 0x4008000 IRQ:7 INTF:TP MEM:6144b MAC 00:02:d7:28:10:b
a
Partition check:
hda: [PTBL] [2584/240/63] hda1
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 320 blocks [1 disk] into ram disk... done.
VFS: Mounted root (ext2 filesystem).
empeg-pump v0.03 (19980601)
Press Ctrl-A to enter pump...03:05: rw=0, want=2, limit=0
dev 03:05 blksize=1024 blocknr=1 sector=2 size=1024 count=1
EXT2-fs: unable to read superblock
Kernel panic: VFS: Unable to mount fs on 03:05